216-587-2885


Savage metal working presses are available in four-post guided platen and straight side, gib guided frame types. Applications include forming, stamping, blanking, bending, piercing, punching, perforating, trimming, transfer, flanging, joggling, forcing, and others.

Savage 4-post press platens are guided on large-diameter, chrome-plated tie rods through eight line-bored bronze bushing assemblies for positive alignment. Two bushings are separated in each extra-long bushing tube for a generous bearing ratio.

Savage straight side presses are used for applications where the tool is not guided, the load is not centered, multiple operations occur or more accurate parallelism is required than a 4-post press offers. Straight side presses have either 45 degree or 8-way adjustable gibbing for a tight running clearance. Exclusive self lubricating gib liners eliminate the need for lubrication systems.

Savage blanking and stamping presses employ robust straight side housing type construction with prestressed tie rods running through the side housing uprights. This type of construction is used on the most demanding applications with off-center loads or break-through shock. Blanking presses feature impact dampers to absorb break-through shock at its origin. They reduce stress on the press, dies and foundation. They also minimize the noise produced during blanking.

Electro-hydraulic controls are available to make any or all of the press functions programmable. The Savage setup controller with touchscreen operator interface is user friendly. At the touch of a finger, the operator can change press set-ups from those stored in memory making set-up faster and consistently repeatable from job to job. Simply enter a job number assigned to a die and the press is ready to run. Optimum pre-established setpoints are automatically entered for tonnage, speed, positions and dwell time values.


350 Ton Straight Side Punch Press

Savage Straight Side Prestressed Housing Press

Straight side prestressed housing press frames employ rigid construction for low deflection levels and eight-way adjustable gibs on self-lubricated ways for precise parallelism.

This type of press is used for more demanding applications such as punching, blanking, trimming, piercing, perforating and multistation dies.

Illustrated is a high speed, punch bend, cut off and emboss press with automatic 3/4" x 4" bar feeder for trailer hitch manufacturing.

More information about this product is available here in the form of a PDF document.

If you do not have a PDF reader, you can download one for free here:


115 Ton Straight Side Trim Press

Savage Straight Side Gib Guided Trim Press

Illustrated is a high speed trim press for heavy cast-iron Honda automotive spindles. The 12" thick solid bed has a through hole for part drop.

The slide is guided at the 4 corners on 45 degree adjustable jibs.

More information about this product is available here in the form of a PDF document.

If you do not have a PDF reader, you can download one for free here:

 

mf2 400 ton straight side housing type metalforming press

60 Ton 4 Post

4 Post Blanking Press

SAVAGE 4 post presses are built with very long bushing tubes to separate 8 bronze bushings for paralelism accuracy. This multistation press blanks sheetmetal disks for Thermos Corporation.

More information about this product is available here in the form of a PDF document.

If you do not have a PDF reader, you can download one for free here:

 

mf2 400 ton straight side housing type metalforming press
400 Ton Prestressed Housing Press

Straight Side Prestressed Housing Type Hot Extrusion Press

Very rigid prestressed tie rod construction for the most demanding applications.

This type of press is designed for adverse conditions such as offset loading, multiple station tools and breakthrough shock.

More information about this product is available here in the form of a PDF document.

If you do not have a PDF reader, you can download one for free here:

mf1 400 ton wheel press/forcing press
400 Ton Inclined Forcing Press

Wheel Press / Forcing Press

Horizontal forcing presses are used to push/pull wheels, sheaves, gears, rolls etc. onto/off shafts or axles.

Model shown is inclined to allow overhead loading. Inserts are available for different shaft diameters. Open design allows work of infinite lengths. Many sizes and models available.

More information about this product is available here in the form of a PDF document.

If you do not have a PDF reader, you can download one for free here:

mf7 1000 ton metalforming press with fully hydraulic cushion
1000 Ton Press with 250 Ton Cushion

4 Post Metalforming Press with Hydraulic Cushion.

Precision Four Post with extra long guides, 120" x 60" diespace and fully guided hydraulic cushion. High speed hydraulics with fully programmable tonnage, speed and position with program storage, QDC and programmable stroke cushion.

More information about this product is available here in the form of a PDF document.

If you do not have a PDF reader, you can download one for free here:

 

mf10 c-frame flanging press with vert. and horiz. rams

230 Ton Flanging Press

 

C-Frame Flanging Press with Vertical and Horizontal Rams

This deep throated press is generally used to form hull plate for ships or to form plate for heavy equipment and fabrication shops. Twin vertical 115 ton rams can be used separated in sequence or can be keyed together for a single 230 ton vertical platen. A 60 ton horizontal ram allows intricate metalforming operations such as flanging, joggling, bending and forming heavy steel plate into complex configurations. These presses have three piece frames held rigidly together with pretensioned tie rods.

More information about this product is available here in the form of a PDF document.

If you do not have a PDF reader, you can download one for free here:

   

 

Engineering, Inc.
4855 Chaincraft Road, Garfield Heights, Ohio USA 44125

Tel: 216-587-2885 - Fax: 216-587-0613